The energy efficiency of Australian houses has profound implications on three key areas:
1. Household costs
2. Australia’s carbon emissions and meeting our international reduction targets
3. The load on the national electricity market
In addition to these, a government study into ACT house prices found that an energy rating improvement of one star would increase market value by three percent on average, which can amount to tens of thousands of dollars.
Homes are a significant contributor to greenhouse gas emissions, accounting for about 11% of Australia’s total carbon emissions. Energy efficiency has been identified as one of the cheapest ways for Australia to cut carbon emissions.
Since May 2011, all new homes or renovations in Australia must meet a minimum six-star or equivalent energy rating (depending on your state or territory).
Unfortunately, Australian standards fall far short of those in Europe and North America and progress is slow. The overall energy intensity of residential buildings in Australia improved by only five percent between 2005 and 2015.
Building designers use special software to ensure that the building plan is consistent with efficiency measures. There are also other rating methods, such as meeting the deemed-to-satisfy (DTS) provisions of the construction code.
The problem is that apart from the initial design stage, there’s typically no further assessment to ensure recommended energy-saving requirements are actually installed, or installed properly. This has resulted in cases where there have been clear discrepancies between the energy rating listed on paper and the actual energy efficiency for some new homes being built.
So ultimately, because an energy-efficient home potentially costs more, consumers may be paying a premium for something they aren’t getting, and anticipating energy savings that aren’t occurring.
In some cases, owners have been shocked when independent assessors rated their homes as far less energy efficient than they were originally told. This could be the result of an incorrect evaluation or an issue with the building and construction of the dwelling.
CHOICE’s investigation into house energy ratings in 2011 found that Australia needs to improve its building energy ratings system in order for it to continue to add value to homes and improve energy efficiency.
Dominic Ogburn is a building consultant and training specialist with more than 25 years’ experience in the building industry. He’s also an NSW Fair Trading Award-winner for advancing consumer protection in the industry. In his opinion, the current regulation of building energy ratings for new homes is “pathetically inadequate”.
“Basically, the building industry is left to self-regulate when it comes to installing energy-savings measures,” he said. “It’s a conflict of interest for some developers who want to employ cost-cutting measures when completing a build.”
But the buck doesn’t always stop with builders. “Energy assessors typically work off the design, so you need to check whether they have the qualifications to perform post-build inspections properly,” says Ogburn.
Ogburn provided CHOICE with evidence of homes that didn’t comply with the plans provided through energy ratings software. One building was missing compliance elements such as a rainwater tank, ceiling fans, properly installed draught seals, ventilation windows in the laundry and ceiling insulation.
“At the end of the day, consumers are paying a premium for a product that is not delivered as specified,” says Ogburn.
A lot of homes leak air, which has a big impact on their energy efficiency. Jan Brandjes tests airflow issues to see if builders have met the gap-sealing requirements.
“I’ve tested hundreds of homes and found them to be consistently leaky. In many cases, exhaust fans in the bathroom and unsealed downlights are causing a lot of air leakage,” says Brandjes.
Fortunately, many of the problems can be fixed easily and for much less than adding other energy-saving measures, such as solar. For a new home under construction, this cost can be as little as $300, or $1000-1500 for existing homes.
Even if you have the highest-performing thermal windows, bad installation can mean you’ll lose a lot of energy efficiency.
Dick Clarke, a building designer with 35 years’ experience in energy-efficient design, is sustainability director for the peak industry body Building Designers Association of Australia. He’s also a technical adviser on the Your Home Technical Manual.
“If you have crappy installation, you will lose energy efficiency,” Clarke says bluntly. “Unfortunately, the certification process allows a conflict of interest that often downgrades the ‘as built’ result from the ‘as designed’ goal.”
Jenny Edwards assesses homes at the design stage for energy-efficiency requirements in the ACT, and is licensed by the Association of Building Sustainability Assessors. She bought a home with a rating of three stars, which was downgraded to a one-star rating after revised calculations. It had a good orientation and sensible levels of window glazing, but she found its thermal potential was significantly overstated.
This was because the assessment didn’t include the 21 unsealed downlights and two exhaust fans without dampeners. The house had also received a good score for wall insulation even though the walls were uninsulated, and ceiling insulation was patchy or non-existent.
Gillian and Stephen Kozicki nearly bought a house in north-western Sydney that required more than $100,000 worth of additional work to meet minimum government building and energy compliance issues, despite being certified for occupation. This was discovered when they asked Dominic Ogburn to audit the house.
The vendor then exercised a contractual right to rescind the sale at the last minute.
Gillian and her family were left looking for a hotel room, and later renting until they found a replacement home. After great time and expense, she complained to the Building Professionals Board, and after eight months, minor disciplinary action was taken.
Given that 38% of home energy use comes from heating and cooling, there are several ways to increase energy savings.
Read more of our tips on heating and cooling your home efficiently.
All new homes and renovations must meet energy-efficiency requirements mandated through the National Construction Code (NCC). It’s then up to the state and territory bodies to implement the code and regulate the industry.
The Nationwide House Energy Rating Scheme (NatHERS), is one method of demonstrating compliance with the NCC’s minimum energy-efficiency standards for new homes.
NatHERS assessments are carried out before construction using software. They rate the energy efficiency of a home’s design and give a star rating out of 10.
The NatHERS tools assess building mass, roof types, insulation, window size and other factors to rate the heating and cooling loads of the building.
The NSW Government’s Building Sustainability Index (BASIX) sets out minimum water use and greenhouse gas emission standards for all new and renovated houses, and is applied at the design phase.
It’s a web-based tool that looks at the location, size, building materials and design of the building. It covers the building envelope’s thermal performance and a wide range of household energy uses by fixed equipment such as heating and cooling appliances, lighting and hot water.
BASIX sets percentage reduction targets for greenhouse gas emissions and water use for houses of a similar size in the same geographical location.
It’s implemented under the Environmental Planning and Assessment Act.
The National Built Environment Rating System (NABERS) is an easy-to-use online calculator for assessing the energy and water use of an existing, occupied home against that of an average household.
It uses information from 12 months of energy and water bills and looks at all appliance usage. It then gives a rating out of six stars, with six stars indicating leading energy performance, three being the median and two, below average.
The NABERS scheme complements other ratings schemes that only assess the design of a building, not the construction, maintenance, appliances or how the occupants use it.
The Green Star national rating system is for new buildings and fitouts including units and townhouses, and is awarded after construction.
Green Star assesses the design and delivery of buildings and fitouts against benchmarks in energy, water, waste, indoor environment quality and ecology.
A Green Star rating is a mark of excellence and buildings must be at least 10% more energy efficient than the requirements under the NCC. There are three rating levels awarded: four-star is ‘Best Practice’, five-star is ‘Australian Excellence’ and a six-star rating represents ‘World Leadership’.